Product Description
Billet Engine-Bay Access Covers for the C8 Corvette Coupe
C8RallyDriver Access Covers replace the stamped-steel factory covers on every 2020+ C8 Corvette coupe with a pair of 6061 billet aluminum covers, finished in anodized color or a factory paint match and badged with the GM Officially Licensed Corvette logo of your choice. They are a direct bolt-on using the factory fasteners, and they are the piece that ties the engine bay together with our RaceLite Hatch Supports and O6G-Ultra B-Pillar Covers.
Choose Your Finish: 27 Colors
Anodized black, red or blue, Edge Red or Edge Blue to match the engine and valve covers, or a factory paint match with 2K clear coat in every factory Corvette paint color. Factory paint match covers ship in 1 to 5 business days.
Choose Your Corvette Logo
Every logo is a GM Officially Licensed design applied as a permanent 3M vinyl graphic. Select it from the menu above:
- Grand Sport or GSX for the 2027 Grand Sport, in Black, Black and Red, Blackout or Galvano.
- Corvette Flags in Galvano, Carbon Flash or Carbon Black, plus the 70th Anniversary flags and Official 70th logo.
- Stingray in Galvano or Carbon
- Z06 in white or black
- E-Ray in white, black or the Official Blue Corvette E-Ray Logo
- ZR1 and ZR1X in black, red or white
- Corvette Racing Official C8.R Jake skull
Prefer an engraved logo in red, black or blue anodized finish? Those are separate products: Stingray, Z51, Z06, E-Ray, ZR1, Flags, C8.R and 70th Anniversary.
Billet Aluminum Specification
Each cover is machined from 6061 billet aluminum to the factory mounting pattern, so nothing on the car is modified and the covers seat exactly where the stamped originals did. New foam water seals come pre-attached.
Anodized finish care
All anodized parts can fade with long-term exposure to UV light, heat and harsh cleaners. To keep the color vibrant, minimize long-term sun exposure (garage storage, car covers) and coat the covers with a UV-inhibiting SiO2 or graphene ceramic spray after washing and on your regular detailing cycle. That also helps prevent mineral deposits and water spots. Do not use chemical or acid-based cleaners on anodized parts.
Will These Access Covers Fit My C8?
They fit all 2020+ C8 Corvette coupes: Stingray, Z51, Z06, E-Ray, ZR1, ZR1X, Grand Sport and Grand Sport X. They do not fit the hardtop convertible (HTC), which has no access covers; see the HTC Fast Access Covers for that car.
What's Included
- Two C8 Corvette Access Covers (one pair) with your selected finish and GM Officially Licensed logo, in a black presentation box
- Eight nylon washers to protect the finish at each fastener
- New foam water seals, pre-attached
Titanium Fastener Upgrade
Upgrade the visible fasteners too with our C8 Corvette Titanium Fastener Kits and the 22-piece Engine Bay Dress Up Bolt Kit Options for access covers, strut tower bars, hatch supports and more in Burnt Blue, Bright Polished, Rainbow Colorshift or Stealth Black titanium finishes.
Installation: Under 10 Minutes
Place tape over the drainage hole just below the access covers so the factory T15 screws cannot be lost. Remove the stamped factory covers and clean the B-pillar. Using the factory screws or titanium fasteners, fit one nylon washer on each fastener, then seat the new covers. Each fastener should turn with little or no resistance; if it binds, it is not seated, so back it out rather than force it. Hand-tighten only, alternating top to bottom until the covers sit straight, and do not overtighten. Install videos for this and every other C8RallyDriver product are on our installation guides page.
